Stories Untold

This guide will help you beat Episode 2 for those who are stuck and get the 2 achievements that are included called “Heat Starter” & “The Chart”

Phase 1:

Experiment 01:
Turn on the Camera by clicking it, Turn on the screen by clicking the switch on its bottom left, switch the screen the XR by moving the slider to the right, click the button on the CC86 machine under the drill, press the Green Button.

Experiment 02:
Switch the screen back to its original state R3, turn on the LZR 11 machine on the bottom right, input 650 for a 650nm lazer(red). Press the Green Button.

Experiment 02-B:
Clear your previous input with the big “C” and input 510 for a 510nm lazer(green). Press the Green Button.

Experiment 02-C:
Clear the previous input again and input 455 for a 455nm lazer(blue). Press the Green Button.

Experiment 03:
Turn off the LZR 11 machine and turn on the Blue Box and the Smaller Box to the right of it. Afterwards spin the dial on the blue box to 250HZ and push the scroller down by 1 next to the dial to the wave symbol. On the smaller box, dial it up 1. Press the Green Button.

Experiment 03-B:
Dial up the Blue Box to 500HZ and the smaller box to 5. Press the Green Button.

Experiment 03-C:
Move the slider on the Blue Box up 1 to the wave with more straight lines on it. Press the Green Button.

Experiment 03-D:
Scroll the dial on the Blue Box to 1000HZ(1Khz) and press the Green Button.

(Unlocked: Heat Starter)

Experiment 04:
Turn off the Blue Box and the Smaller Box next to it, then turn in the drill by clicking on it. Press the Green Button.

Experiment 05:
Click the handle for the containment box.
Click on the light.

Phase 2:

Look through the memories
Look - Around
Use - Computer
Use - Airlock
Look through the memories
Look - Around
Use - Wreckage
Look - Light
Go - Figure
Memories
Look - Around
Read - Writing
(Unlocked: The Chart)
Use - Wires
Go - Door
Memories
Use Device
Pattern
1st - The one that is already there
2nd - Move 1 to the right
3rd - Move 2 to the right
4th - Move 3 to the right
Memories
The End

EPISODE 2 – THE LAB CONDUCT

You'll be performing experiments, and will have controller movement on the experiment screen. Access the experiment by pressing : Y if you need to zoom in for more detail.

Experiment 1
1. Click Camera (Top Middle) – Red Light Will Turn On
2. CC86 (Left) - Click The Switch In The Center Of It – Blinking Red Light
3. Turn On The TV (Top Right) – It's The Red Square Button In The Bottom Left Corner Of The TV
4. Click TV Slider Bar – Display Will Say XR
5. Sync Master (Bottom Left) Blinking Green Light - Click The Big Green Button


Experiment 2
1. Click TV Slider Bar – Display Will Say R3
2. Turn On LZR II (Bottom Right) – Programing to 650 NM
3. Click The Sync Master (Bottom Left)

4. Go Back To The Experimente
5. LZR II – 510 NM
6. Click Sync Master

7. Go Back To The Experimente
8. LZR II – 455
9. Click Sync Master (((Achievement – HEART START)))

Experiment 3
1. Directly Under The TV Is A Digital Signal Generator - Turn It ON
2. Click The Digital Signal Generator Slider Bar Once (Middle Symbol Selected)
3. Click The Digital Signal Generator knob – Hold A And Move The Left Thumbstick Until It Reads 250
4. Right Of The Digital Signal Generator Is A Basaline AMP - Turn It ON
5. Click The AMP Knob – Hold A And Move Until It Reads 1
6. Turn Off The LZR II
7. Click Sync Master

8. Go Back To The Experiment
9. Digital Signal Generator – 500
10. AMP Knob – 5
11. Click Sync Master

12. Go Back To The Experimente
13. Digital Signal Generator – Click The Slider Bar So The Top Symbol Is Selected
14. Click Sync Master

15. Go Back To The Experiment
16. Digital Signal Generator – 1000
17. Click Sync Master


Experiment 4
1. Turn On The Drill (Red Thing On Top Of The CC86)
2. Turn Off The Digital Signal Generator And AMP
3. Click Sync Master

Experiment 5
1. Click The Left Handle To Open The Box (Middle)
2. Click Orb x2 (Cutscene In Between)

3. You Should Now Be Told To Use The Computer. We're Back To Using LB To Bring Up Commands To Enter.

4. Look – Around
5. Use – Computer
6. Go – Airlock
7. (Click The Orb)
8. Look – Around
9. Look – Wreckage
10. Use – Wreckage
11. Look – Around
12. Go – Figure
13. (Click The Orb)
14. Look – Around
15. Look – Writing
16. Read - Writing (((Achievement – THE CHART)))
17. Use – Wires
18. Go – Door
19. (Click The Orb)
20. Use – Device

21. Use The D-Pad To Set The Glyphs In The Right Column. The Top One Is Already Set.
22. The Second One, Press Right x1.
23. The Third One, Press Right x2.
24. The Fourth One Press Right x3

25. Click The Orb (((Achievement – REVOLT)))